Sold out. We can let you know when it is available.
The SALICRU SPS 1000 HOME+ is a 1000 VA / 600 W Line-interactive UPS in an eight-outlet Schuko power-strip format. It is intended to protect computer workstations, network equipment, NAS systems, routers, modems, switches, cameras and other electronics against power cuts, voltage fluctuations and surges.
The Buck/Boost AVR corrects mains voltage variations without continuously using the battery. If mains power fails, the UPS transfers to battery operation in a typical 2–6 ms, with a maximum of 10 ms, and provides a 230 V AC pseudo-sine-wave output. The documentation specifies compatibility with APFC loads of 410 W.
All eight outlets are surge protected and six also provide battery backup. This version adds a Master-Slave function: one Master outlet can control three Slave outlets according to the power drawn by the main device. The switching threshold can be set to 40, 70 or 100 W.
The USB HID interface allows connection to a computer and use of Power Master software for Windows, Linux and Mac for monitoring and controlled shutdown. One USB-A and one USB-C charging port provide a combined 5 V / 2.4 A output.
The internal 12 V / 9 Ah sealed Pb-Ca AGM battery is maintenance-free and user-replaceable. Cold Start, automatic battery charging, automatic restart, UPS and battery-level LEDs, audible alarms, a removable cable organiser and wall-mounting points are also provided.
Laser printers and other high-consumption or high-inrush-current loads should only be connected to the surge-protected outlets rather than the battery-backed outputs.
| Model | SPS 1000 HOME+ |
| Salicru reference | 693DA000003 |
| Technology | Line-interactive |
| Format | Multi-outlet power strip |
| Power rating | 1000 VA / 600 W |
| Rated input voltage | 230 V AC single-phase |
| Input voltage range | 162–290 V AC |
| Rated input frequency | 50 / 60 Hz, auto-detect |
| Voltage stabiliser | AVR Buck/Boost |
| Input protection | 10 A resettable thermal breaker |
| Rated output voltage | 230 V AC single-phase |
| Voltage accuracy in battery mode | ±10% |
| Waveform in battery mode | Pseudo-sine wave |
| Output frequency | 50 / 60 Hz, same as input |
| Frequency accuracy in battery mode | ±1 Hz |
| Transfer time | 2–6 ms typ.; 10 ms max. |
| APFC load compatibility | 410 W |
| Output outlets | 8 Schuko |
| Battery-backed and surge-protected outlets | 6 |
| Surge-protected-only outlets | 2 |
| Battery | Sealed Pb-Ca AGM, maintenance-free |
| Battery configuration | 1 × 12 V / 9 Ah |
| Recharge time | 8 h to 90% charge |
| User-replaceable battery | Yes |
| Battery protection | Overcharge, deep discharge and short-circuit |
| Communication | USB, HID protocol |
| Monitoring software | Power Master; Windows, Linux and Mac |
| USB charging ports | 1 × USB-A + 1 × USB-C |
| USB charging output | 5 V / 2.4 A total |
| Master-Slave function | 1 Master outlet + 3 Slave outlets |
| Master-Slave thresholds | 40 W / 70 W / 100 W |
| Cold Start | Yes |
| Automatic battery charging | Yes, even when switched off |
| Automatic restart | Yes, after end of backup time |
| Protection rating | IP20 |
| Operating temperature | 0–40 °C |
| Storage temperature | −20–50 °C |
| Relative humidity | 0–90%, non-condensing |
| Maximum operating altitude | 3000 m |
| Acoustic noise at 1 m | 20 dB |
| Dimensions | 335 × 185 × 122 mm |
| Weight | 5.8 kg |
| Standards | EN-IEC 62040-1, EN 62040-2, EN 62040-3 |