Available
Acrylic insulating conformal coating for printed circuit boards and electronic assemblies, formulated from a methacrylic copolymer to form a clear protective film. It is intended to improve protection for equipment exposed to aggressive environments such as humid or dry heat, mist and salt-laden air.
The coating is flexible, provides very good adhesion, is silicone-free and contains a fluorescent tracer visible under ultraviolet light. This tracer allows the uniformity of the applied coating to be checked visually without changing the transparent finish.
The current technical data sheet states a dielectric strength of 100 kV/mm, surface resistivity of 9 × 10¹² Ω and dielectric constant of 2.9 at 100 Hz. It also states climatic resistance for 500 h at 95% relative humidity and 55 °C, together with 192 h salt-spray testing in a saturated atmosphere.
The coating can be used from −45 to +140 °C, with a stated peak temperature of 200 °C. It is solder-through, allowing local PCB repairs without first removing the complete coating. The manufacturer also states fungicidal behaviour, resistance to yellowing and resistance to flaking.
Before application, the surface should be clean, dry and degreased. Contacts that must remain conductive should be masked before spraying. Shake the aerosol thoroughly and spray upright from approximately 15–25 cm away in thin, slightly overlapping coats. The manufacturer recommends three coats with 15–20 minutes between coats.
The current technical data sheet gives a full cure time of 24 hours, which may be accelerated in an oven. After spraying, the manufacturer recommends turning the can upside down and purging the nozzle until only propellant gas is released, helping to keep the spray system clear.
This is a professional-use product. The current SDS classifies it as an extremely flammable aerosol, a serious eye irritant and capable of causing drowsiness or dizziness. Use only outdoors or in a well-ventilated area, keep away from ignition sources and do not expose the container to temperatures above 50 °C.
| Product type | Acrylic insulating conformal coating aerosol |
| Coating base | Methacrylic copolymer / acrylic resins |
| Applications | Printed circuit boards, components and electronic assemblies |
| Coating colour | Transparent / colourless |
| UV tracer | Yes; fluorescent under ultraviolet light |
| Silicone | Silicone-free |
| Flexibility | Yes |
| Adhesion | Very good, according to the manufacturer |
| Fungicidal behaviour | Stated by the manufacturer |
| Yellowing resistance | Does not yellow, according to the manufacturer |
| Flaking resistance | Does not flake, according to the manufacturer |
| Dielectric strength | 100 kV/mm |
| Surface resistivity | 9 × 10¹² Ω |
| Dielectric constant | 2.9 at 100 Hz |
| Hardness | 161 s, Persoz pendulum |
| Climatic resistance | 500 h at 95% RH and 55 °C |
| Salt-spray test | 192 h in saturated atmosphere |
| Coating operating range | −45 to +140 °C |
| Stated peak temperature | 200 °C |
| Solder-through coating | Yes; allows local PCB repairs |
| Recommended spraying distance | 15–25 cm |
| Recommended number of coats | 3 thin coats |
| Time between coats | 15–20 min |
| Full cure time | 24 h |
| Specified thinner | Ethyl acetate |
| Mixture density | 0.914 g/cm³ |
| Water solubility | Insoluble |
| Net contents | 400 ml |
| Aerosol format | 650/400 ml |
| Use | Professional / industrial |
| UFI | GYCN-D0X8-R00X-DK5T |
| Current CLP classification | Aerosol 1; Eye Irrit. 2; STOT SE 3 |
| H222 | Extremely flammable aerosol |
| H229 | Pressurised container: may burst if heated |
| H319 | Causes serious eye irritation |
| H336 | May cause drowsiness or dizziness |
| EUH066 | Repeated exposure may cause skin dryness or cracking |
| Maximum aerosol storage temperature | < 50 °C |
| UN number | UN 1950 |
| Transport class | 2.1 |